[MF-1]

• The Bank Mode is not working anymore...

• Has it got inputs for volume pedals?

• Can I permanetly save the 0-127 mode?

• Can I solder my midicable to add the phantompower capability?

[MF-2]

• I want to use a sustain type pedal as well as my expression pedal. The sustain pedal would be used to send a control change of 127, and then zero again (if it is latched).

• The "middle" dot of the display is blinking - what does it mean?

• It is possible to send more then one Midiprogramchange at the SAME time to my gear? E.g. can I switch to channel-1 program-54 and simultaneously to channel-3 program-23?

• Which Expression Pedal is recommended for the [MF-2]?

Effect Pedals

• Could you please tell me if your pedals are true-bypass?

Other

• Please explain how to download the circuit diagrams

• I lost the powersupply of my SST-19, can you give me the technical details?

• I want to run the output of an electric guitar or bass directly into a PA system...

[MF-1]  The Bank Mode is not working anymore...

• The slideswitch on the backsite is damaged. Either a pin is ripped of or one the copperwires is damage

[MF-1]  Has it got inputs for volume pedals?

• Sorry the MF-1 hasn't. But the MF-2 has!

[MF-1]  Can I permanently save the 0-127 option?

• Sorry - this is not possible!

[MF-1]  Can I solder my midicable to add the phantompower capability?

• Yes - Others did it too. Please note: Do it at your own risc- no warranty.

• The connection is shown in the owners manual. The connection is shown from the backside (contact-side)

[MF-2]  I want to use a sustain type pedal as well as my expression pedal.

• The switch must be wired to the RING and TIP of a stero jack

[MF-2]  The "middle" dot of the display is blinking - what does it mean?

• Look at the ownersmanual: (4.4 BACKUP BATTERY)

• The MF-2 uses an internal lithium battery to hold the internal data (memory) during power
  off. The life is approx. 5~7 years. The MF-2 permanently checks it's state. If the backup battery
  is down, the middle point of the 3 digit LED DISPLAY will flash. Save all data (MIDI DUMP
  TRANSMIT) and exchange the battery by an authorized service center.

• The battery is soldered, which means a skilled technician is needed to do the replacement job!

[MF-2]  It is possible to send more then one Midiprogramchange at the SAME time?

• Yes - this is the main job of the MF-2.

• You can switch up to 16 midiprogramchanges + 4 external switching operations.

[MF-2]  Which Expression Pedal is recommended for the MF-2?

• There are currently no expression pedals available from Nobels. We recomend the Yamaha™ Expression Pedal FC-7.

• Recommended technical data: Potentiometer 50Kohm / Linear. (Different curves can be selected from the menu)

[Effect Pedals]  Could you please tell me if your pedals are true-bypass?

• No - the pedals switch electronically which means without popnoise.

[Other]  Please explain how to download the circuit diagrams

• Go to the register page

• Choose a product.

• Enter name, company and your emailaddress

• Click the register-button

• A new page appears: Click the download link

• or use the right mouse button to download the file to your desired directory

• After successfully downloading the file doubleclick to open

• or if it not works, please reinstall the Adobe Acrobat Reader®

[SST-19]  I lost the powersupply of my SST-19, can you give me the technical details?

• AC: 2 x 6,6 Volt 1A. (XLR Plug: Pin 1 (Middlecontact) = GND, 2 and 3 is AC. Please note: AC NOT DC!

[DI-Box]  I want to run the output of an electric guitar or bass directly into a PA system...

• Normally you can go directly from your bass into the pa-system...

• You need a DI-Box to decouple two grounded systems. E.g. You have a (grounded with the powerplug) Bass-Preamp (system I) and want to connect to (grounded too) the pa (system II) This combination may creates HUM-NOISE which can be prevent using a DI-Box.